Pipe cutting machine Avangard LS-50-1200
Avangard LS-50-1200 band saw is designed for sawing plastic pipes and shells up to 1200 mm in diameter at angles from 0 to 45 degrees to the longitudinal axis of the workpiece. The machine is manufactured in accordance with the requirements of GOST 25223 in the climatic version UHL 2 according to GOST 15150.
AvangardLS-50-1200Avangard LS-50-1200 pipe cutting machine
Video of the pipe cutting machine Avangard LS-50-1200.
2018-11-07T16:19:27The LS-50-1200 bandsaw machine is designed for sawing plastic pipes and covers up to 1200 mm in diameter at angles from 0 to 45 degrees to the longitudinal axis of the workpiece.
The band saw head of the machine, mounted on a rotary platform, moves at a given angle to the cut pipe along high-precision guides.
The cut pipe is fixed on the supports, which can be completed (optional) with a rolling trolley for pipes longer than 6 meters.
The machine can be manufactured without a saw block u-turn unit.
Cost of the machine without the saw block u-turn unit
Cost of a rolling trolley for pipes up to 12 m long
To install the machine at the desired cutting angle of the workpiece, you must:
- lift the support screws (from the floor);
- turn the machine to the desired angle on the limb;
- fix the machine position with the support screws.
Two u-turn nodes are used to turn the tape 90 degrees. The upper u-turn unit is mounted on an adjustable rod that allows you to change the length of the u-turn section of the tape depending on the size of the workpiece to be sawed.
The portable machine control panel on the front panel has:
- machine emergency shutdown button 1;
- the stop button of the main drive 2;
- main drive power button 3;
- warning light 4;
- feed speed controller 5;
- the power button and the feed forward 6;
- the stop button feed 7;
- back feed button 8.
The machine consists of the following main components:
- frames 9;
- four saw wheels protected by casings 8;
- the rotary platform 5 with a rail guide (by) 4;
- the base frame of the machine 2;
- nodes (upper and lower) of the saw belt u-turn 6;
- tension mechanism of the saw belt with hydraulic tension 10.
The frame of the machine 9 is a welded structure mounted on a movable trolley 5, which can be moved along the rail guides 4 in the direction of the workpiece and back.
The rail guides, in turn, can be deployed along the segment base 2 to the desired sawing angle. Four guide support wheels of the saw belt are mounted on the machine frame on adjustable supports. The lower wheels are mounted on a sliding frame consisting of movable and fixed forks. The saw belt is tensioned by extending the forks with the hydraulic tensioning mechanism 10. In this case, the force on the movable fork is transmitted through a special damper, and the belt tension force is controlled by the hydraulic pressure gauge. The recommended tension force is 11 MPa.
Technical specifications of the Avangard LS-50-1200 band saw pipe cutting machine
Diameters of the pipe to be cut | mm | 1200 |
Pipe length | not limited | |
Angle of cutting relative to the end of the pipe | degree | 0 ± 45 |
Saw band: | ||
- length | mm | 12370 |
- width | mm | 34 |
- thickness | mm | 1,1 |
The speed of the saw tape | m / sec | 9,3 |
Power of the electric motor of the saw blade drive | kW | 7,5 |
Power of the electric motor of the feed drive | kW | 0,25 |
Power supply voltage | V | 380 |
Overall dimensions: | ||
- width | mm | 6700 |
- height | mm | 4300 |
- length | mm | 6000 |
Weight | kg | 4000 |